The Journal · November 17, 2026 · 7 min read · By Émilie, Head of Content
Libraries, dressing rooms, kitchens, full-height doors: joinery is the trade that sets a high-end renovation apart from a simple refurbishment. It is also the one least easily fixed when it is thought of too late. Here is how it is designed, made and installed.
In short
On our sites, two separate trades share the wood. Interior joinery gives the apartment its lines: full-height doors, restoration of moulded doors and espagnolette bolts, skirting, casings, panelling. Fitted furniture creates the pieces that become part of the walls: libraries, dressing rooms, kitchens, bathroom vanities, window seats, radiator covers, hall storage.
In a Haussmann apartment, the joinery challenge is often to restore what exists and to create the new in the same vocabulary, so the eye cannot tell old from contemporary. The fitted-furniture challenge is to give every square metre a use, without the storage showing.
Off-the-shelf furniture is designed for straight walls and 2.5 m ceilings. A Paris apartment has neither: walls out of square, ceilings over three metres, recesses, ducts, sealed fireplaces, low windows. A standard unit leaves filler strips, voids above the cabinets and gaps against the walls.
Bespoke is therefore not a decorative luxury. It is the only way to use the full height, absorb the irregularities of an old building and align every front, joint and handle with the design of the room.
The difference shows inside as much as outside: concealed hinges, handle-free or integrated pulls, full-extension drawers, lighting that switches on as the door opens, veneered rather than melamine interiors. These are the items that move the budget most, and the ones you notice every day.
Successful joinery is fully drawn before it is made. The order is always the same:
Bespoke is decided at the start, not the end. A library full of books needs reinforcement in the partition; a lit dressing room, a power supply inside the unit; a bathroom vanity, a water supply in the right place. All of this is planned while the walls are open. Decided after painting, joinery means reopening what was finished.
An apartment to fit out? Tell us about your project in a few lines: we come back to you within 48 hours with a first reading of scope, order of magnitude and a realistic timeline.
At W.A.R.D, bespoke joinery and fitted furniture for a complete project come to €500 to €700 per square metre of apartment, €600/m² on average. This is added to the price of the renovation itself (€1,800 to €2,200/m² for a complete renovation, €2,400 to €2,800/m² for the high end) and to design fees. Applied to a few sizes, that gives the following orders of magnitude:
| Apartment size | 80 m² | 120 m² | 180 m² |
|---|---|---|---|
| Range (€500 to €700/m²) | €40,000 to €56,000 | €60,000 to €84,000 | €90,000 to €126,000 |
| Average (€600/m²) | €48,000 | €72,000 | €108,000 |
These are calculated orders of magnitude, not the budget of an actual project. What moves the figure: the length of furniture (a fully fitted apartment, or only the kitchen and one dressing room), the fronts (lacquer or a rare wood veneer), the hardware and integrated lighting. Our article on the cost of a Haussmann renovation details the rest of the budget.
Hiring a joiner alone makes sense for a single piece in an apartment that is already finished. In a renovation, joinery depends on almost every other trade: the electrician for integrated lighting and hidden sockets, the plumber whenever a unit takes a water point, the plasterer for reinforcements and plumb walls, the painter for the finish. It is one of the sixteen trades we coordinate under a single contract, on a single schedule.
At the Trocadéro, a former 227 m² law office turned into an apartment, joinery was one of the sixteen trades coordinated over ten months. To see the level of finish we aim for, browse our projects, or our page on apartment renovation in Paris.
At W.A.R.D, bespoke joinery and fitted furniture for a complete project come to €500 to €700 per square metre of apartment, €600/m² on average. This is added to the price of the renovation and to design fees; it varies mostly with the length of furniture, the fronts and the hardware chosen.
Usually eight to sixteen weeks of manufacturing after the shop drawings and samples are approved. That is why joinery is drawn during design and goes into production during the first months of the works.
Both have their place. Solid wood suits parts with little surface movement: frames, worktops, thick shelves. For large panels and full-height fronts, a wood veneer on a stable core warps far less with changes in humidity, while keeping the look and feel of wood.
You need a precise drawing, not necessarily an extra party. W.A.R.D designs joinery in-house, or builds from your interior designer's drawings; either way, the shop drawings are approved with you before manufacturing.
"Many thanks to Anthony and his team for their professionalism, their advice and the quality of the work. The result is refined and exactly what I expected." (translated)Adrien A. · Google review
Read the reviews →Just a question? Write to us — answer within 48 h, no commitment.